FREQROL-A are located at the front) with screws or bolts. .. (The A inverter does not contain the switching connector unlike the and Find new and reconditioned A Series Mitsubishi Inverter Drives at EU Automation. Free 1 year warranty on all parts. Discover more by visiting us now. : NEW MITSUBISHI FR AEK UL, FREQROL-A, V AC FR A HP,BOXZO: Everything Else.
|Published (Last):||10 March 2017|
|PDF File Size:||17.54 Mb|
|ePub File Size:||15.38 Mb|
|Price:||Free* [*Free Regsitration Required]|
Magnetic Flux Vector Control Effective for eliminating noise in the frequency setting circuit.
Factory setting DC dynamic brake voltage t t 7. Setting in Pr. Notes on Wiring 1 The power must not be applied to the output terminals U, V, Wotherwise the inverter will be damaged. Setting E r r? A larger set value results in x lower response.
Mitsubishi FREQROL A Drive Inverter Fr-aek-ul – 10 HP Torque | eBay
I Check motor and cables for ground fault. List Only the parameters which have been changed in setting are displayed on part of the screen. If the unit is operated incor- rectly, the parameters of the inverter to which the parameters have been copied may be corrupted and normal operation not performed. Have any questions about this item? Hence, the cooling fan must be changedevery 2 to 3 years if theinverteris runcontinuously. The most likely cause of the fault is displayed.
I U Combined operation using the external input signals and parameter The running frequency is set by The external input signal start switch is unit the external input signal, and invalid.
Watch list is full. Contact your sales representative if the corresponding fault is not found below, the inverter has failed, the part has been damaged, or any other fault has occurred.
Shipping cost cannot be calculated. Inverter reset can also be executed in the PU help menu. Check that the following function parameter setvalues are proper: Also, thejumperacrossterminals PR-PX must be removed. Also aummatically selects the accslera- Pr.
Note that the motor capacity must be 0. When the selective monitor screen is not the first priority screen as in the above operation, the selected data is erased from the memory as soon as the power is shut off w200 the other operation mode such as external operation is selected.
Serves as a clear key in the all parameter a00 or alarm history clear mode. Normally set 60Hz in Pr. Jump frequency avoldance areamatch the actual speed. These displays are selected by the following method: See the following function comparison list: When 5 years have elapsed, the capacitor deteriorates more rapidly.
No items may be removed before termination of the sale. When the magnetic flux vector control mode has been selected in Pr.
Check that the motor is connected properly. Any accident due to the leakage current is not covered by our warranty. Otherwise, the reac- tor will not operate. This amount is subject to change until frerqol make payment. When a machine restart is to be prevented at freqrool restoration, provide a magnetic contactor MC in the primary circuit of the inverter and also make up a sequence which will not switch on the start signal.
If so, reduce the torque boost set value. This item may be a floor model or an item that has been returned to the seller after a period of use. W General 2 Check for loose screws and b l k. PU disconnection is not detected. Reset input normally enabled. Contact the seller – opens in a new window or tab and request a shipping method to your location.
Speed greatly differs from the pre- Maximum frequency Pr. Terminal P1 is freqrop for the FR-A If operation cannot be resumed within thenumber of retry times Retry count exceeded Provided Freqrlo set. This parameter need not be setwhen the magnetic flux vector control mode has been selected in Pr. Back to home page.
Mitsubishi FREQROL A200 Drive Inverter Fr-a220e-7.5k-ul – 10 HP Torque
The jumpers between R-R1 and S-S1 must be removed. Operating Procedures 1 Directly entering the Pr.
Operation Mode Descrlptlon Remarks The inverter is operated with the Factory-set to select this operation mode at nverter start switch, frequency setting power on. PU level meter Setting Pr. Output stop SD 4 Setting example Pr.
Mouse over to zoom – Click to enlarge.